Crops

NDVI for orchards: what a satellite canopy check can and can't tell you

FieldSafe team · Draft, scheduled

NDVI is a number from satellite images that tracks how green and dense a canopy is. For orchards, free Sentinel-2 images are good at showing which Block, or which part of a large Block, is behaving differently from its own past. They cannot show you a single sick tree, and they never tell you why something changed: the satellite shows where, not why.

Used that way, a satellite check is a cheap early warning that tells you where to walk first.

NDVI in one picture

Healthy leaves absorb red light for photosynthesis and reflect a lot of near-infrared light, which our eyes can’t see. Bare soil, dry grass and stressed leaves reflect the two more evenly. NDVI (Normalised Difference Vegetation Index) compares the two and gives a value between -1 and 1. Dense, active canopy sits high. Bare ground sits low.

Two related indices are useful on farms:

IndexWhat it leans towardsIn plain words
NDVICanopy greenness and density“How much active leaf is there?”
NDREChlorophyll in denser canopies, using the red-edge band“Is a thick canopy as green as it looks?”
NDMIMoisture in the leaves“Is the canopy drying out?”

Each of these is a pointer. A drop can come from water stress, a nutrient problem, pests, disease, pruning, a hailstorm, a burst irrigation line, or simply new weeds between the rows. The number can’t tell these apart.

What a 10 m pixel means for tree crops

The European Copernicus programme’s Sentinel-2 satellites pass over South Africa every few days. Their images come in pixels of about 10 to 20 metres, depending on the band. A 10 m pixel covers 100 square metres. In a macadamia orchard planted at 8 by 4 metres, that is roughly three trees, plus the ground between the rows. At 20 m, it is more than ten trees.

So be clear about what you are looking at:

  • Single trees: no. One dying tree is lost in the pixel it shares with its neighbours and the inter-row.
  • A patch of trees: sometimes. A wet corner, a stressed slope or a section where the irrigation failed can show up if it covers several pixels.
  • A Block over time: yes. This is where satellite data is strongest. Is this Block greener or weaker than it usually is at this time of year?

Young orchards make it harder. When the canopy covers only part of the ground, the pixel is mostly soil and grass, and cover crops or weeds can move the number more than the trees do. Comparing a young Block with a mature one tells you mostly about their age.

That is why FieldSafe compares each Block with its own past, never with an absolute “healthy” value. A Block of 15-year-old avocados and a Block of three-year-old macadamias will never have the same NDVI. What matters is whether each one has moved away from its own usual.

Clouds are the other limit. Sentinel-2 is an optical satellite, so cloudy days give no usable picture. FieldSafe screens cloudy passes out, which means in a wet spell you may wait longer for a clear view.

Spotting a weak Block

FieldSafe’s satellite monitoring is a premium option, switched on per farm by FieldSafe support (pricing is not set yet). Once it is on, a manager can ask “What do you want to know?” and pick a question: where is the weakest ground, what is better than last time, which Block is behind, or what is drying out.

The Vigour lens

The Vigour lens puts every Block in one table. Each row shows the Block’s latest clear NDVI against its usual value, with a chart of the last 8 passes. A Vigour column makes it easy to sort, and the table exports to CSV.

FieldSafe Vigour lens: a Block's satellite NDVI compared with its own usual value
The Vigour lens: a Block's latest clear NDVI compared with its own usual value, with the last 8 passes.

Areas to check

When part of the farm changes more than usual, FieldSafe raises an Areas to check alert with before and after pictures. It also shows what happened on this Block between two image dates, so you can line up a change in the picture with your own records: a spray, a feeding, a pruning job, an irrigation fault.

A practical example

Pieter manages a fictional 45-hectare macadamia and avocado farm near Politsi. In late October the Vigour lens shows his Block 7 avocados well below their usual for the third pass in a row. His other avocado Blocks are steady. Areas to check marks the lower third of Block 7.

The satellite can’t tell Pieter what is wrong. So he opens what happened on the Block between the two image dates: no spray or feeding was missed. He sends Thandi, his supervisor, to walk the lower section that afternoon.

Then scout it

This is the step that turns a coloured map into a decision. The satellite points; a person on the ground finds the reason.

Thandi finds wet soil and yellowing leaves along the bottom rows. A valve on the lower irrigation line has been stuck open since a power cut, and the low end has been waterlogged for weeks. She records a scouting walk on the Block with photos, and a job goes in to fix the valve. Without the satellite, the problem would likely have been found only when the trees looked bad from the road.

A good habit:

  1. Check the satellite view weekly in the busy season, or after any storm.
  2. Look for change against the Block’s own past, not for the “greenest” Block.
  3. Walk the flagged area and record what you find, with photos.
  4. Link the cause to a record: a job, a problem report, a scouting finding.
  5. Watch the next clear passes to see if the Block comes back.

Other ways to see your orchard from above

Satellite monitoring in FieldSafe is one option among several. Each has a place.

FruitLook

FruitLook is a free service funded by the Western Cape Department of Agriculture. It gives growers in the Western Cape satellite-based information on crop growth, water use and related measures for orchards and vineyards. If you farm in its coverage area, it is well worth using, and it has a long track record with local growers. Check the current FruitLook site for what it covers and where.

FieldSafe’s angle is different: the satellite view sits next to your farm’s own records, so a change in a Block can be read against the sprays, feeding and irrigation you recorded, and turned straight into a scouting walk or a job.

Drones

Drones fly low, so their pictures can show single trees and rows in fine detail. That makes them the right tool when you need to count trees, find individual sick trees, check a new planting or map a problem in detail. Specialist drone and imagery companies offer this as a service, often with expert analysis included.

The trade-off is cost and frequency. A drone flight is a booked visit, while Sentinel-2 passes every few days whatever you do. Many farms will find a mix works: the satellite as a frequent, Block-level early warning, and a drone flight when something needs a closer look.

If you already have drone images, FieldSafe lets a manager upload a drone map (a Cloud-Optimised GeoTIFF with its flight date) and show it over the satellite picture on the farm map.

When to pay for more detail

  • You need tree-level answers: counts, gaps, single sick trees. Consider drones.
  • You are in the Western Cape and want free orchard and vineyard data. Look at FruitLook first.
  • You want Block-level trends linked to your own records, with alerts that lead to scouting. That is what FieldSafe’s satellite view is for.

See your Blocks from space

FieldSafe is in early access and is tested on a staging environment with a few test users. To see how a satellite canopy check sits next to your own records, apply for early access. Read more on satellite and NDVI, how a flagged area turns into a scouting walk on scouting and traps, what a macadamia season looks like on the macadamia page, and how growers share pest pressure in scouting groups.

FieldSafe helps you prepare; certification is decided by your certification body.

Early access

Be one of the first farms on FieldSafe.

FieldSafe is in early access. Join, and we help you set up your farm and try it on your team's own phones.

Join early access